Pull Test in Garments: Method, Standard & Acceptance Criteria
A Pull Test is a critical mechanical test used to verify the attachment strength of accessories like buttons, snaps, and rivets. It ensures that small parts do not detach during wearing or washing, which could cause buyer rejection or severe safety hazards (choking) for children.
This test is a mandatory part of Garment Quality Control and is strictly monitored during the Pre-Production Meeting (PPM).
Which Accessories Must Be Tested?
Acceptance Criteria (Minimum Force)
While standards vary by buyer (e.g., H&M, Gap, Walmart), these are the general industry standards:
| Garment Category | Minimum Force (Newton) | Minimum Force (KG) | Duration |
|---|---|---|---|
| Adults Wear | 70 Newton | ~ 7.14 kg | 10 Seconds |
| Children's Wear | 90 Newton | ~ 9.17 kg | 10 Seconds |
| Infants (0-36 Months) | 90 Newton (Strict) | ~ 9.17 kg | 10 Seconds |
Pull Test Procedure (Step-by-Step)
Follow this Standard Operating Procedure (SOP) using a calibrated Pull Test Machine (like SafQ or Testex):
- Machine Calibration Check the machine with a standard weight (e.g., 5kg or 10kg weight) to ensure the dial reads correctly before starting.
- Select Grip Choose the correct claw/grip. Use a "Three-Prong Grip" for buttons and a "Upper Snap Grip" for snap buttons.
- Fixing the Garment Place the garment fabric securely in the lower clamp of the machine. Ensure the fabric is flat.
- Attaching the Accessory Attach the upper hook/grip to the button or accessory being tested. Ensure a tight grip.
- Apply Force Pull the lever or press the start button. Apply force gradually until it reaches the target (e.g., 90N).
- The "Hold" Phase Once 90N is reached, hold it there for 10 Seconds.
- Final Result If the button remains attached without fabric tearing or thread breaking, it PASSES.
Common Failures & Causes
| Failure Type | Likely Cause |
|---|---|
| Button Detaches | Weak stitching, wrong thread tension, or insufficient number of stitches. |
| Snap Comes Off | Improper pressing pressure (too low) during attachment machine setup. |
| Fabric Tears | Fabric is too weak or no Interlining/Fusing was used for reinforcement. |
| Component Breaks | Poor quality raw material of the plastic or metal accessory. |
Test Report Format
A proper Pull Test Report must include:
- Date & Time of Test
- Style Number / PO Number
- Accessory Type (Size/Color)
- Force Applied (e.g., 93N)
- Result (Pass/Fail)
- Technician Signature
Standards & Compliance
- ASTM F963: Standard Consumer Safety Specification for Toy Safety (Used for Kids Garments).
- EN 71: European Safety Standard.
- 16 CFR 1501: US regulation for small parts (Choking Hazard).
Frequently Asked Questions (FAQ)
A: It should be done at three stages: 1. Mock-up sample (Before production), 2. Inline (Daily during production), and 3. Final Audit.
A: The entire batch is quarantined. The machine pressure or stitching method must be adjusted, and 100% of the pieces must be re-checked or re-worked.
Conclusion
The Pull Test is not just a quality check; it is a safety assurance. Ensuring your accessories withstand 90N force protects your brand from lawsuits and ensures the safety of the end consumer. Always follow the Buyer Tech Pack specifications strictly.
গার্মেন্টস পুল টেস্ট: পদ্ধতি, স্ট্যান্ডার্ড এবং গ্রহণযোগ্যতা
পুল টেস্ট (Pull Test) হলো একটি যান্ত্রিক পরীক্ষা যা বোতাম, স্ন্যাপ বা রিভেটের মতো এক্সেসরিজগুলো কাপড়ের সাথে কতটা শক্তভাবে লাগানো আছে তা যাচাই করতে ব্যবহৃত হয়। এটি নিশ্চিত করে যে পোশাক পরার সময় বা ধোয়ার সময় এক্সেসরিজগুলো খুলে পড়ে যাবে না, যা শিশুদের জন্য শ্বাসরোধের (Choking Hazard) কারণ হতে পারে।
এটি গার্মেন্টস কোয়ালিটি কন্ট্রোল এর একটি অবিচ্ছেদ্য অংশ এবং PPM মিটিং এ এটি নিশ্চিত করতে হয়।
কোন এক্সেসরিজগুলোর টেস্ট করা হয়?
গ্রহনযোগ্যতা বা একসেপ্টেন্স ক্রাইটেরিয়া
বায়ারভেদে এটি ভিন্ন হতে পারে, তবে সাধারণ স্ট্যান্ডার্ড নিচে দেওয়া হলো:
| পোশাকের ধরন | ন্যূনতম শক্তি (নিউটন) | ন্যূনতম শক্তি (কেজি) | সময়কাল |
|---|---|---|---|
| বড়দের পোশাক | ৭০ নিউটন | ~ ৭.১৪ কেজি | ১০ সেকেন্ড |
| বাচ্চাদের পোশাক | ৯০ নিউটন | ~ ৯.১৭ কেজি | ১০ সেকেন্ড |
| নবজাতক (০-৩৬ মাস) | ৯০ নিউটন (কঠোরভাবে) | ~ ৯.১৭ কেজি | ১০ সেকেন্ড |
পুল টেস্ট করার পদ্ধতি (ধাপে ধাপে)
মেশিন ব্যবহার করে সঠিকভাবে টেস্ট করার নিয়ম (SOP):
- মেশিন ক্যালিব্রেশন কাজ শুরুর আগে একটি স্ট্যান্ডার্ড ওয়েট (যেমন ৫ কেজি) দিয়ে মেশিনের কাঁটা ঠিক আছে কিনা চেক করুন।
- গ্রিপ নির্বাচন এক্সেসরিজ অনুযায়ী সঠিক গ্রিপ বা হুক নির্বাচন করুন। বাটনের জন্য একরকম, স্ন্যাপের জন্য অন্যরকম।
- পোশাক সেট করা মেশিনের নিচের ক্ল্যাম্পে কাপড়টি শক্তভাবে আটকান। খেয়াল রাখবেন কাপড় যেন সোজা থাকে।
- আটকানো উপরের হুক বা গ্রিপ দিয়ে বোতাম বা এক্সেসরিজটি শক্ত করে ধরুন।
- টান দেওয়া ধীরে ধীরে শক্তি প্রয়োগ করুন যতক্ষণ না এটি টার্গেটে (যেমন ৯০ নিউটন) পৌঁছায়।
- ধরে রাখা কাঙ্ক্ষিত শক্তিতে পৌঁছানোর পর ১০ সেকেন্ড ধরে রাখুন।
- ফলাফল যদি বোতামটি না ছিঁড়ে বা সুতা না কাটে, তবে এটি PASS।
সাধারণ ফেইলিয়র এবং কারণ
| সমস্যা | সম্ভাব্য কারণ |
|---|---|
| বোতাম খুলে আসা | দুর্বল সেলাই, সুতার টেনশন কম বা সেলাই সংখ্যা কম হওয়া। |
| স্ন্যাপ খুলে আসা | অ্যাটাচ করার সময় মেশিনের প্রেসার বা চাপ কম ছিল। |
| কাপড় ছিঁড়ে যাওয়া | কাপড় দুর্বল অথবা রিইনফোর্সমেন্ট (ফিউজিং) ব্যবহার না করা। |
| এক্সেসরিজ ভেঙে যাওয়া | এক্সেসরিজের কাঁচামালের মান খারাপ ছিল। |
স্ট্যান্ডার্ড এবং কমপ্লায়েন্স
- ASTM F963: টয় সেফটি স্ট্যান্ডার্ড (বাচ্চাদের পোশাকের জন্য ব্যবহৃত)।
- EN 71: ইউরোপীয় সেফটি স্ট্যান্ডার্ড।
- 16 CFR 1501: ছোট পার্টসের জন্য ইউএস রেগুলেশন।
সাধারণ প্রশ্ন ও উত্তর (FAQ)
উত্তর: এটি ৩টি ধাপে করা উচিত: ১. মক-আপ স্যাম্পল (উৎপাদনের আগে), ২. ইনলাইন (উৎপাদন চলাকালীন প্রতিদিন), এবং ৩. ফাইনাল অডিট।
উত্তর: পুরো ব্যাচটি আটকে (Quarantine) রাখতে হবে। মেশিনের প্রেশার ঠিক করে বা রি-ওয়ার্ক করে ১০০% চেক করার পর পাস করতে হবে।
উপসংহার
পুল টেস্ট শুধুমাত্র একটি কোয়ালিটি চেক নয়, এটি নিরাপত্তার নিশ্চয়তা। ৯০ নিউটন শক্তি সহ্য করার ক্ষমতা নিশ্চিত করার মাধ্যমে আপনি বায়ারের ক্লেইম থেকে বাঁচতে পারেন এবং শিশুর নিরাপত্তা নিশ্চিত করতে পারেন। সর্বদা বায়ার টেক প্যাক মেনে চলুন।